How to seal drafty windows

Learning how to seal drafty windows can improve comfort, reduce dust and insects, and limit heat loss during the Australian winter. The main challenge is identifying whether air enters around a movable sash, through a failed frame seal, or around the window opening itself. Each source needs a different repair, so choosing the wrong product may leave the draught untouched or cause the window to stick.

Australian conditions also affect the method and timing. Across southern and eastern Australia, June to August is the main cool season, while Tasmania and alpine regions can experience frosty mornings and freezing nights. Brisbane and other humid areas can develop condensation during the warmer months, and older homes may combine timber sashes, aluminium sliders, brick veneer, or fibro cement surrounds. A suitable repair should suit both the window construction and the local climate.

Find the air leak before buying a seal

Start by deciding whether the problem is moving air or glass that simply feels cold. A draught usually comes from a gap around the sash, a worn brush seal, a loose frame, or an opening that no longer closes evenly. Cold glass indicates heat loss through the glazing, which a new perimeter seal may not fully solve. Noise, dampness, and insects can also enter through small openings that are difficult to notice.

Close the window and move a thin tissue slowly around its edges. Where the tissue is pulled or pushed, the air leak is usually close to the surface. Closing doors and turning off ceiling fans can create a slight pressure difference that makes weak leaks easier to detect. A thermal camera can also reveal temperature differences, although it is not necessary for a straightforward home repair.

Inspect the sash for distortion, damaged corners, loose catches, and worn strips. Look for peeling paint, water marks, daylight, or debris trapped in the frame track. The same seasonal inspection used for broader seasonal home maintenance can help identify changes before they become major problems.

Prepare the window and choose the right seal

Work during dry, mild weather and follow the temperature limits printed on the product. Remove loose paint, flaking sealant, dust, and old adhesive from the contact area. Repair any soft timber rot or cracked render first, then allow filler or primer to dry completely. A clean, dry surface gives adhesive strips a stronger grip and helps fresh silicone form a reliable seal.

Compression foam and V-strips suit gaps around hinged or lifting sashes. Brush pile or narrow weather strips work well for sliding windows, while flexible silicone sealant is intended for fixed joints and small cracks. Australian hardware counters such as Bunnings, Mitre 10, and local suppliers commonly sell these products in rolls or lengths measured in metres. Match the strip depth to the gap rather than forcing a thick profile into a narrow space.

Cold snaps make draft prevention especially valuable in Tasmania, the Australian Alps, and elevated areas. A practical guide to preventing frozen pipes offers useful companion advice for preparing the rest of the home when temperatures fall sharply.

Fit brush seals to moving sashes

For a hinged window, measure each side of the sash and choose a compression seal that fits the rebate or stop. Cut each piece to length, peel back a short section of backing, and press the strip onto clean timber or metal. Keep the adhesive flat and avoid stretching it, because tension can cause the seal to peel away near the corners.

Work around the window one section at a time, testing the latch and sash movement after each piece. Butt adjoining sections closely at the corners and press their edges down firmly. Replace a bottom sweep if air rises strongly from the sill, but check that it does not scrape against the frame or prevent the window from closing. A sash should still open smoothly and remain available for emergency escape.

Sliding windows need a different approach. Fit a low-friction pile or slim brush strip along the sash edges, but leave the rollers and drainage channels unobstructed. Do not pack foam into the bottom track, where it can collect grit and stop the sash sliding. Security and insect screens must remain clear, removable, and functional rather than being permanently sealed to the moving sash.

Use sealant only on fixed joints

Silicone is useful around the fixed outside edge of a frame or where a stationary trim meets masonry, but it should not be placed between a sash and its frame. Moving parts need clearance, and a rigid bead of sealant can bind the window or crack as the timber expands. Window putty should also not be used as a substitute for a proper moving sash seal.

Apply sealant to a clean, dry joint and mask nearby surfaces if necessary. Cut the nozzle at an angle, lay a continuous bead, and tool it smooth with a wet fingertip or suitable applicator. Allow it to cure for the time stated on the tube before operating the window. Wider gaps may need an appropriate backing material so the sealant does not simply sag into the opening.

Avoid covering external weep holes, drainage paths, or designed ventilation gaps. Those features remove rainwater and trapped moisture from the frame. Keep combustible security screens and bushfire-related clearances in mind as well, because added seals should not obstruct the screen or create a new fire hazard. Summer sun and UV exposure can harden poor-quality products quickly, so exterior silicone suited to Australian conditions is preferable.

Finish with a practical seasonal check

Retest the window after the repair with the same tissue method used earlier. Look for movement around the full perimeter and inspect from outside after rain, when water tracks may reveal a remaining gap. If smoke or an aerosol draft indicator is used, keep it well away from the opening and follow monthly smoke alarm checks to confirm the alarms remain operational.

Condensation needs a different response from a draught. Fogging on the inside of the glass often results from humid room air meeting a cold pane, especially in Brisbane, Darwin, and warm coastal districts. Better sash seals can reduce moving-air infiltration, but ventilation, blinds, insulation, and moisture control may also be needed. Persistent black mould around the frame or sill should be investigated rather than simply covered with sealant.

Clean the tracks and wipe movable seals regularly, then inspect them before winter and after severe weather. Replace crushed foam, loose brush strips, or brittle sealant promptly rather than waiting for the whole window to fail. The practical takeaway is to match the product to the gap: use compression or brush weather strips where parts move, flexible sealant only at fixed joints, and finish with a fresh draught test.